Nation Wide Surplus

Home · Valve types · Brands

Sell Fisher 657 Diaphragm Actuators

A 657 tag on top of a valve identifies the actuator, not the body underneath it. Nation Wide Surplus evaluates Fisher 657 diaphragm actuators, loose spares and complete control packages. Send its own size and serial identification alongside the valve and instrument labels so each part of the assembly stays identifiable.

Call 832-721-8398 · Upfront payment in most cases

What we buy

Submit unused 657 maintenance stock, project leftovers, used actuators and complete valve assemblies. Identify handwheels, positioners and loose mounting components separately. If several actuators came from a dismantled plant, preserve which body and controller belonged to each one.

Model identification guide

Fisher 657 is a direct-acting spring-opposed diaphragm actuator for sliding-stem valves. The 657 schematic shows air pushing the stem down and the spring lifting it. Record the full actuator model, size and serial number; the valve-body model and controller model are additional identities.

Nameplate locations

Start with the actuator nameplate on the accessible exterior of the assembly and photograph the complete plate. Include a wide view showing where it belongs. Look for separate valve and instrument plates rather than treating one tag as the identity of everything. When a plate is hidden or unreadable, send visible markings and matched records.

Actuator sizes and travel

The referenced 657 manual covers sizes 30/30i through 70/70i and 87. Preserve the i designation when present. An actuator size number is not a pipe diameter. Record nameplate travel and any available stem or yoke information without assuming that visually similar sizes fit the same valve.

Materials and exterior construction

Describe the actual casing, yoke, exposed stem and visible condition; photograph material markings if present. Do not assign internal spring or diaphragm materials from exterior paint. Replacement parts and rebuilt equipment need their own records. State when an alloy or elastomer specification is unconfirmed.

Pneumatic pressure and bench-set information

Send the nameplate bench-set range and maximum casing-pressure information when readable. These are actuator data, separate from the valve-body pressure class. Do not substitute a general family limit or a regulator setting for the actual actuator rating. This buying guide does not provide pressure-setting or commissioning instructions.

Mounting and stem connections

Show the yoke, stem connector and mounting interface as supplied. The 657 manual lists size-specific yoke and stem dimensions; the 657 number alone does not prove a match to a loose valve. Keep associated hardware identified with the correct assembly.

Valve-body combinations

ET, EZ, ES and ED are body-family names that may appear with diaphragm actuator assemblies. Identify the actual valve separately and preserve its full model, size and class. Listing related guides does not establish that every actuator size is compatible with every body.

Fisher ET valve guide

Fisher EZ valve guide

Fisher ES valve guide

Fisher ED valve guide

Positioners and FIELDVUE controllers

Photograph the exact positioner or DVC label, mounting bracket and visible feedback components. Explain whether instruments are mounted, loose or missing. Keep the controller’s suffix and hardware labels separate from the actuator size.

DVC6200 identification and buying guide

Positioner buying hub

Actuator action versus valve fail position

Direct-acting describes the actuator response; it does not by itself prove whether the complete valve fails open or closed. Valve plug action and assembly configuration also matter. Send the actual assembly records rather than promising a fail position from “657” alone.

Where this equipment is found

Check control-valve spare racks, retired process skids and project closeout inventories. A work order tied to the actuator serial number can explain why it became surplus. Distinguish equipment removed during an upgrade from units removed for a reported fault.

What photos to send

  • Entire 657 actuator and any attached valve.
  • Full actuator plate, size and serial identification.
  • Yoke, exposed stem, connector and visible condition.
  • Separate controller, regulator and accessory labels.
  • Handwheel, packaging and matched repair or test records.

What information to send

List quantity by model and size, condition, equipment location and any known service history. Include travel, bench set and mounting details from the plate or records when available. State what is missing, whether items are still installed and any deadline. For complete packages, send all three identities: valve, actuator and controller.

Condition considerations

Show corrosion, dented casings, bent or damaged stems and incomplete mounting parts. A clean repaint does not establish diaphragm or spring condition. Include dated repair reports when they match the serial number, and disclose known leaks or operating problems.

How payment works

We provide upfront payment in most cases. Payment terms are agreed with you before pickup or shipping.

Shipping and pickup

Measure the entire actuator including its yoke, handwheel and mounted instruments. Complete control-valve packages need their own dimensions and weight. Provide pallet count and loading access. Pickup, suitable parcel shipment or brokered freight is arranged for the lot, location and agreed purchase.

Fisher 657 seller FAQs

Does a 657 nameplate identify the valve body?

No. Photograph the body and controller labels separately.

Is actuator size the valve size in inches?

No. Preserve the actuator’s own size and the valve’s nominal size as separate fields.

Does 657 alone establish fail-open or fail-closed?

No. Include the actual valve and assembly configuration records.

Can I submit a standalone actuator?

Yes. Send its full identification, mounting condition and location.

Should I disassemble the spring housing for photos?

No. Initial evaluation starts with accessible exterior labels and the assembly as supplied.

More seller questions

Request a 657 purchase evaluation

Send the full plate, show what is included and tell us where the equipment is.

Send equipment details

Call 832-721-8398 or email jcostello@nationwidesurplus.net. Include the equipment location and a phone number where we can reach you.

Identification references

Technical product identities are checked against manufacturer documentation. These references do not establish the condition of your equipment or a manufacturer affiliation.

Scroll to Top